Tuesday, October 30, 2018

Orleans Barber

Orleans Barber

Hook - Gamakatsu T10-6H or equivalent

Thread - Black

Tail - Barred wood duck

Body - Red chenille

Hackle - Grizzly

Reference - Steelhead Fly Fishing & Flies - Trey Combs

Black Spook

Black Spook

Category - Steelhead

Hook - Gamakatsu T10-6H

Thread - Black

Tail - Golden pheasant crest

Ribbing - Flat gold tinsel

Body - Red yarn

Hackle - Black

Wing - White bucktail

UV Resin

Steelhead Fly Fishing & Flies - Trey Combs

Saturday, October 27, 2018

Magic Midge

Magic Midge

Hook - Curves style

Thread - Black

Body - Black thread

Legs - Black z-lon, crystal flash etc

Thorax - Dubbing

Wing - White biot

Sunday, October 14, 2018

Sicilian Gold

Sicilian Gold

Hook - Salmon/steelhead style

Thread - Orange thread

Tip - Embossed tinsel

Tail - Red hackle fibers

Ribbing - Embossed tinsel

Body - Yellow floss or uni-stretch

Wing - Orange under white bucktail

Head - Orange thread

UV Resin

Reference - Steelhead Fly Fishing and Flies - Trey Combs & Trout Flies Volume Two - Terry Hellekson

Tying note - The Trey Combs book has the tip/tail in reverse order while the Terry Hellekson book omits the white bucktail in the wing, I tied the above fly usin the Trey Combs recipe and I reversed the tip/tail.

Saturday, October 13, 2018

Silly Stilly

Silly Stilly

Hook - Salmon/steelhead style

Thread - Black

Tail - Orange hackle fibers

Butt - 3 turns orange chenille

Body - Orange yarn

Wing - Orange over white bucktail

Reference - Steelhead Fly Fishing and Flies - Trey Combs

Pacific King

Pacific King

Hook - Salmon/steelhead style

Thread - Black

Tail - Black hackle fibers

Body - Insect green floss with a strip of brown floss laid over the

top and secured with 4 turns of black tying thread ribbing

Throat - Black hackle fibers

Wing - Black squirrel tail

UV Resin

Reference - Steelhead Fly Fishing and Flies - Trey Combs

Sunday, October 7, 2018

Mike Tucker Stonefly - Pteronarcys Californica

Recipe

Pteronarcys Californica

Hook - Mustad 9672; Size 4 (or the size of stone flies in your area)

Thread - White flat waxed nylon for building the body:

8/0, 10/0 or 12/0 tan thread for tying the rest of the fly

Tails, antenna and legs - 12 or 20 pound fly line backing colored with a brown marker

Under body - Thread and seamstress or map pins to help build a flat taper to the under body

Over body - Clear liquid lace, larva lace, v-rib, body glass etc

Wingpad - 1/4 inch wide tyvek paper colored with a brown marker

Thorax - Orange dubbing

Marker - Brown and orange for this fly but other colors can be used to suit

the stone flies in your area. A salmon colored marker can be used for the underside.

Markers can be whatever brand you like to use.

Cut 2 pieces from the fly line backing for the tails. Leave these uncolored for now.

They will be colored with a brown marker in a later tying step.

Cut 6 pieces from the fly line backing for the legs and color with brown marker.

Take a 1/4 wide piece of tyvek paper and fold it in half lengthwise.

Trim the end in an approximate 45 degree angle to form a vee notch as shown.

Prepare 2 strips of tyvek paper for the wing pads and 1 strip for the pronotum as shown above.

The lighter and bodkin will be used later to bend the legs.

Tying Procedure

Tie on thread and wrap to the bend. Wrap a bump of thread to help separate the tails.

Tie in the tails and the v-rib and begin to build a tapered body. I'm using v-rib for this fly but if you choose a liquid or larva lace, you may fill the tubing with oil, water etc.

Attach a dressmakers or map pin to the side of the body to determine its length.

The point of the pin should be at the forward end of the thread bump.

The pin should be cut to length from the forward end of the thread bump to the forward end of the tapered body.

Cut both pins to the same length and tie on to the body. Ensure the pins are tied on parallel to the hook shank. The purpose of the pins is to create a horizontal taper to the under body.

Wrap the tying thread to fully cover the pins.

Color the underside of the body with the lighter marker (for this fly - orange)

Color the top side og the under body, thread bump and tails with the darker marker

(for this fly - brown)

Wrap the v-rib forward to create the over body shell.

Trim off excess material and the flat waxed nylon thread.

Tie on 8/0, 10/0 or 12/0 tan thread for tying the rest of the fly.

Tie on one of the previously prepared tyvek hind wing pad and fly line backing legs.

Trim off all excess materials.

Dub the back end of the thorax with a dubbing of your choice. (for this fly - orange)

Tie on the second set of legs. Trim off excess materials.

Tie on the other previously prepared tyvek hind wing pad. Trim off all excess material.

Tie on a 1/4 inch wide strip of tyvek paper over the body of the fly.

Dub the front end of the thorax with a dubbing of your choice. (for this fly - orange)

Tie on the third set of legs. Trim all excess materials.

Tie on the fly line backing antenna and then pull the strip of tyvek paper forward to create the pronotum. Trim off all excess materials and build a neat tapered head.

The following steps require caution.

Using the lighter, heat up the bodkin (not to cherry red) and while hot, gently press the bodkin against one of the legs to bend the leg approximately 90 degrees. This will melt the fly line fibers of the fly line backing in contact with the heated bodkin just enough to keep it bent. Repeat on the other side.

CAUTION: A too hot bodkin will cut right through the fly line leg like butter!